8 Different Methods of Concrete Crack Repair | How to Select Suitable Method of Concrete Crack Repair
Table of Contents
Introduction of Concrete Repair Method
Concrete is one of the most widely used building materials in the construction industry all over the world. Concrete is a versatile construction material that possesses various advantages as compared to other construction materials.
There are many defects that occur in the concrete with time due to an aggressive environment. There are many old structures that have reduced their strength in due time. If further use of such buildings continued it will endanger the lives of the people and the surrounding habitat.
Here In this article, we will learn about the various concrete repair methods in detail which are used to repair concrete damage. Concrete repair is basically a modification of the concrete due.
How to Select Suitable Method of Concrete Crack Repair?
The concrete repair method which is adopted for the restoration of this structure mainly depends upon the cause and the extent of the damage.
The concrete repair method is selected based on the evaluation of the crack that occurred in the structure. While treating any damage or crack in the concrete structure it is very necessary that we should know the main cause of that defect.
Knowing the cause of the damage and reducing or eliminating that cause will repair last longer. The selection of the concrete repair method also depends upon the various factors which are as follows. Importance of the structure.
- Availability of Suitable Material.
- The Function of the Structure.
- Nature of the Damage.
- Availability of the Fund.
Methods of Concrete Crack Repair
There are various concrete repair methods which are used to repair various types of cracks and damages which generally occur in the concrete.
1. Method of Concrete Crack Repair: Stitching
In the technique of stitching the crack is a bridge up with u shaped metal, you need stitching dogs before being repaired with the rigid resin material.
This can establish restoration of the strength and integrity of the correction due to care is to be given to make an analysis check to ensure that this will perform well under applied loads.
Stitching is the best concrete repair method for Major cracks and it is suitable when tensile strength must be re-established across the major cracks.
Stitching will not close the crack but it is a way of stopping the further movement of active cracks. Stitching will help to prevent cracks from spreading.
Stitching dogs should be of variable length and orientation and so located that the tension transmitted across the crack is not applied to a single plane within the section but is spread over an area.
2. Method of Concrete Crack Repair: Grouting
Grouting is also one of the common and widely used concrete repair methods. Grouting is defined as the process in which the injection of liquid grouting material into the concrete under pressure.
During the process of grouting, the cracks and pores in the concrete get filled with the grouting material which will get subsequently Hardened.
Grouting can be performed the same as the injection of epoxy.
The Procedure of the Process of Grouting
The step-by-step procedure for grouting are as follows.
- First upon holes are drilled along the crack in this structure and in and around hollow spots.
- If there are several cracks the holes can be drilled in a staggered manner at 500 mm to 750 mm spacing in both directions covering adequately the area proposed to be grouted.
- The holes spacing can be changed as per the requirement and the site conditions.
- The Galvanized Iron pieces ( 12 to 20 mm diameter X 200 mm) with one end threaded or PVC nozzles are fixed in the holes with rich cement mortar.
- All the cracks and annular space around G.I. pipes are filled with rich cement mortar.
- All the cracks are cut open to a ‘V’ shaped groove, cleaned, and sealed with rich cement mortar.
- All the ground holes will be closed with water using the same equipment a day before grouting.
- All holes are first plugged with proper wooden logs are locked in the case of PVC nozzles. The bottom-most plug and the two adjacent plugs are removed and cement water injected in the bottom-most hole under pressure.
- When the cement water comes out through the adjacent holds the injection of cement mortar is stopped and the plugs in the bottommost hole and the one immediately above are restored.
- The process of grouting of concrete cracks is repeated with other holes till all the holes are covered properly.
- It is important that on the day of routing all the flags should be removed in order to drain out the excess amount of cement water and restore before starting the process of grouting.
- The grout should be kept fully stirred under pressure throughout the process of Grouting. The grouting is carried out till refusal and till crowd starts flowing from the hole present at its adjacent.
- A proper record of the quantity of grout injected into each hole should be maintained.
- After the process of grouting, it is very necessary that proper curing should be done for or at least 14 days. All the equipment which are used in the process of grouting should be clean thoroughly after its use.
Precautions Should Be Taken During the Process of Grouting of Cracks in Concrete
- In the case of the arch masonry of the bridges, the grouting is done to strengthen the structure. Some load tests may be carried out in selected structures to satisfy that grouting has helped to reduce the deflection of the crown and spread at the springing to within permissible limit.
- After completing the grouting work, all the equipment which are used in grouting including the slurry and mixing drums, nozzles should be thoroughly washed otherwise cement will get set.
- After the grouting work is completed it should be inspected thoroughly by the expert and should be kept under observation for a period of 6 to 12 months for its behavior after grouting.
3. Method of Concrete Crack Repair: Epoxy Injection
The epoxy injection is the most widely used concrete repair method for cracks which generally develops in beams and columns. The injection of a low viscosity epoxy is a possible repair method for cracks.
This concrete repair method proves to be effective to completely fill the cracks. The epoxy injection is a concrete repair The method is suitable for the treatment of cracks between 0.02 mm and 6mm.
While treating the cracks, care should be taken that the crack must be free of dirt grease, and other types of contamination. This is the best method of crack sealing of concrete.
The use of low modulus and flexible attitude in the treatment of crack will not allow significant movement of the concrete structures.
Before starting this process it is very necessary that the dust should be cleaned by using vacuum cleaning. Compressed air or blasting with water can also be used to remove dust and other contamination from the crack.
If the dust and other contamination are not removed from the crack, then epoxy resin will not form a strong bond in a crack. Epoxy injection is a concrete repair method in which the epoxy concrete is prepared by the addition of epoxy resin with a hardener in the appropriate proportion.
For epoxy injection, high skilled workmanship is required for its application. The injection should start from the bottom and continue until resin appears at the next port.
The injection nozzle is removed from the seal and the nozzle moved up to the next port. It is very just that the pumping pressure should be properly maintained in the cracks.
At the end, when the injected resin gets cured properly the sealing adhesive should be removed by using grinding or cutting.
The various methods of providing entry ports are as follows
- Bonded flush fitting which is attached by the sealing adhesive.
- The drill holes with the systematic fitting inserted and bonded with the adhesives which are used for the purpose of sealing.
- The interrupted seal using a gasket that covers the unsealed portion.
4. Method of Concrete Crack Repair: Grooving and Sealing
Grooving and sealing is the most common and simple Concrete repair method. This technique can be executed with relatively unskilled personnel and can be used to seal both fine pattern cracks and larger isolated cracks.
The system can be used to repair dormant cracks that are of no structural significance and is used to seal the cracks against the increase of moisture and carbon dioxide.
This concrete repair method involves enlarging in the crack along with its export face and sealing it with crack fillers. The care should be taken to ensure that the entire crack is routed and sealed.
5. Method of Concrete Crack Repair: Guniting
Guniting is the concrete repair Method in which the mortar is conveyed through a hose pneumatically to protect at a high velocity onto a surface.
This technique has been developed by introducing a small-size coarse aggregate into the mix. This process is made economical by reducing the cement content. The force of Jet impact on the surface compact the material.
6. Method of Concrete Crack Repair: Shotcreting
The shotcrete process is used for the application of mortar of less thickness. It is also a concrete repair method that is used to repair various damages in concrete structures. Shotcreting works on the same principle of greeting for achieving greater thickness with a small coarse aggregate.
Step by step procedure of shotcreting are as follows.
- Shotcreting is a concrete repair method. The first one removes the Plaster and finishes all around the distressed concrete surface.
- Remove concrete all around the reinforcement in order to get an average 25mm air gap.
- Put the additional information wherever the reinforcement diameter has been reduced by more than 15 to 20%.
- Fix shear key bars of appropriate diameter at a specified spacing in both directions over the surface to be covered with repair materials.
- Apply appropriate passivating and Bond Court over the reinforcement and prepared RCC surface.
- Shotcreting should be done with a 6mm thick finishing coat. It is also necessary to do wet curing over the finished surface of the shotcrete for a minimum period of 7 days.
7. Method of Concrete Crack Repair: Dry Packing Method
Dry packing is a concrete repair method for filling holes and cracks whose depth is at least equal to the smallest surface dimension of the repair area.
The dry pack method is generally used on a small hole in the concrete. The holes should be at least 25 mm deep the dry packing method is not suitable for shallow depressions. The holes go right through the concrete section where the filling cannot be properly rammed.
Dry pack mortar is normally a mix of one part of ordinary Portland cement to 2.5 part of fine sand. The correct measure of the water will produce a mortar that is at the point of becoming rubbery when it is solidly packed.
The holes should be prepared so that they are sharp and Square at the surface edge. The interior surface is to be rubbed and if possible undercut marginally. All repairs and effects to concrete must be removed and the surface of the hole left clean.
Dry should be packed in a layer that has a compacted thickness of about 10 mm. The compacting effort should be directed at a slight angle towards the sides of the hole. The holes should not be overfilled and can be done by pounding on a piece of hardened laid on the surface.
The holes are vertical or overhead surface or not likely to be prepared effectively by this method and epoxy mortar is may be needed. The area to be prepared properly by cleaning and roughened and it should be kept wet for some time.
Repair mortar should be mixed to a plastic consistency and a small quantity of cement mortar should be scrubbed into the surface with the wire brush.
Repair mortar compacted should be a tight Filling around the edges of the hole. It is necessary that proper curing should be done for at least 7 days.
A strong and good bond will get developed between old concrete and repair. The expansive cement or admixtures have been advocated for replacement mortar repair. Generally, the expansive admixtures are used for grouting purposes.
Also Read: 10 Different Between Mortar And Concrete | What Is Mortar & Concrete | Types of Mortar & Concrete
8 . Method of Concrete Crack Repair: Drilling and Plugging
This concrete repair method consists of drilling down the length of the crack and Grouting it to form a key. This concrete repair method is used to repair vertical cracks in the retaining walls.
The hole should be drilled on the crack and the grout key prevents transverse moments of the section of the concrete adjacent to the crack. The key will also help to reduce the heavy leakage through the crack and loss of soil from behind a leaking wall.
Conclusion of Method of Concrete Crack Repair
The above Concrete repair methods are used for repairing concrete defects and cracks which generally occur in concrete structures. The use of the particular concrete repair method varies upon the types.
[su_box title=”FAQ” style=”default” box_color=”#333333″ title_color=”#FFFFFF” radius=”3″ class=”” id=””]
Concrete Repair Method
- Patching
- Resurfacing
- Crack injection
- Concrete overlays
- Shotcrete repair
- Carbon fiber reinforcement
How to Fix Cracks in Concrete?
How to Fill Cracks
- Chisel out the crack to create a backward-angled cut.
- Clean out any loose material from the crack.
- Apply a thin layer of bonding adhesive.
- Mix and trowel reinforced patching compound into the crack.
How to Fill Cracks in Concrete?
- Prepare the crack
- Choose a suitable filler
- Apply the filler
- Smooth the surface
- Allow curing and drying
How to Fill Large Cracks in Concrete?
You can either fill the crack with sand leaving ¼ inch to the surface of the crack to be filled with the grout or make multiple grout applications that are ¼ inch thick, allowing adequate time for each application to dry. Wet the crack slightly and begin filling it in with grout, applying layers no thicker than ¼ inch.
Repairing Crack in Concrete
- Evaluate the crack
- Clean the crack
- Choose a suitable repair material
- Prepare the crack
- Apply the repair material
Concrete Crack Filler
Crack Filler for Concrete is an acrylic compound specially designed to repair concrete floors, mortar joints, sidewalks, steps, pool decks, roughcast and any other concrete or masonry surface.
What Is the Best Concrete Crack Filler?
Latex-based products, including Sakrete Crack Filler and Sakrete Concrete Repair offer good performance – suitable for cracks up to 3/8” deep and 1/2″ wide. Latex-based products offer easy clean-up and will last for a couple of years depending on application conditions.
How Do You Fill Cracks in Concrete Before Epoxy?
Patcher paste is a great way to fill cracks and holes in concrete before you apply your epoxy. It will cure quickly, so it’s easy! Concrete is a popular floor base because it offers a long lifespan and durability. However, over time concrete is known to form cracks.
Will Concrete Sealer Fill Cracks?
It easily fills small holes, cracks, and imperfections in your concrete surface and adds to the durability and longevity of your concrete floor.
Should Cracks in Concrete Be Sealed?
Cracks are present in every concrete slab, and they are unavoidable due to the rigid nature of concrete. Uneven drying, shrinkage and temperature changes can all cause fractures in your slab. To avoid water seepage and further damage, it’s critical to seal any cracks that develop.
Are Hairline Cracks in Concrete Slabs Normal?
Hairline cracks in a concrete slab are rarely a cause for concern. They can be controlled, but not eliminated. A crack in a slab of 1/8 inch or less is typically a normal shrinkage crack and not a cause for concern.
How to Repair Concrete Crack?
- Assess the crack
- Clean the crack
- Choose a suitable repair material
- Prepare the crack
- Apply the repair material
How to Seal Cracks in Concrete?
- Clean the crack
- Choose a suitable sealant
- Prepare the crack
- Apply the sealant
How to Patch Cracks in Concrete?
- Prepare the crack
- Choose a suitable patching material
- Prepare the patching material
- Apply the patching material
Can Cracked Concrete Be Repaired?
Wide cracks in concrete are best patched and sealed with a concrete patching compound. Smaller cracks, less than 1/4 inch wide, can be repaired with a concrete caulk or liquid filler. Patching compounds typically are mixed with water and applied with a trowel.
Should You Fix Hairline Cracks in Concrete?
Hairline cracks or cracks under 1/4-inch wide may not indicate serious underlying damage, but if water gets into them and repeatedly freezes and expands, and vehicles continue to drive over them, the cracks can get bigger and the problem can worsen. These cracks can usually be repaired.
Concrete Wall Repair Methods
Concrete Wall Crack Repair in 7 Steps
Step 1: Scrub it Clean.
Step 2: Use a Nail to Align Injection Points.
Step 3: Mix the Two-Part Epoxy Crack Sealer.
Step 4: Spread the Sealer onto the Base.
Step 5: Mix and Apply a Larger Batch of Epoxy Sealer.
Step 6: Dispense the LCR Epoxy.
Step 7: Fill Up the Ports.
Crack Repair Techniques
Concrete Crack Repair Methods
- Epoxy injection grouting.
- Routing and sealing.
- Flexible sealing.
- Stitching.
- Providing additional reinforcement.
Concrete Slab Repair Methods
There are only three choices when it comes to repairing a settled or sunken concrete slab: replace it, grind it, or raise it. Before the use of polyurethane and Poly jacking, the common methods of raising and supporting a slab was by mudjacking.
Concrete Crack Repair
Step 1: Remove the Loose Concrete. Remove any damaged or crumbling concrete.
Step 2: Clean the Concrete. Clean the area in and around the damage with a wire brush and broom.
Step 3: Position the Concrete Patch Form.
Step 4: Mix the Concrete Crack Sealer.
Step 5: Smooth the Concrete Patch.
Concrete Slab Crack Repair
- Evaluate the crack
- Clean the crack
- Choose a suitable repair material
- Apply the repair material
Best Concrete Crack Filler
- Quikrete Concrete Crack Seal
- PC-Concrete Two-Part Epoxy Adhesive Paste
- Sikaflex Self-Leveling Sealant
- DAP Concrete Patch and Resurfacer
Concrete Patio Crack Repair
- Widen the Crack. Widening the crack and creating a V-shape will help the patch materials stick better.
- Clean Out the Crack.
- Add the Solid Crack Filler.
- Apply the Concrete Crack Filler.
- Flatten the Filler.
- Let the Patch Cure.
Grouting Method of Crack Repair
Injection grouting is the method of filling the cracks, open joints, voids, or honeycombs, in concrete or masonry structural members. This is done under pressure with a grout material that cures in place to produce the desired results like strengthening a structure and preventing water ingress.
Best Concrete Crack Repair
Epoxy injection is a common method for repairing structural cracks in concrete. It involves injecting an epoxy resin into the crack, which fills and bonds the crack, restoring the structural integrity of the concrete. Epoxy injection is typically used for wider or deeper cracks, and it provides excellent strength and durability.
Crack Repair
Concrete crack sealants and caulks are the most common product used to fill cracks in concrete. They come in squeeze tubes and can be applied right into the crack with a caulking gun. Both do a good job of keeping out water and bugs.
Concrete Crack Patch
When it comes to patching concrete cracks, there are various effective products and methods available. The best choice for your specific situation depends on factors such as the type and size of the crack, the desired strength and durability of the patch, and the application method. Here are a few popular options for concrete crack patching:
[/su_box]
[su_note note_color=”#F2F2F2 ” text_color=”#333333″ radius=”3″ class=”” id=””]
Like this post? Share it with your friends!
Suggested Read –
- All About Wood | Types of Wood | What Is Wood | Advantages of Wood
- What Is Spalling Concrete | Causes of Spalling in Concrete | Repairing Concrete Spalding
- What Are Curb and Gutter | Types of Curb and Gutter| Advantages & Disadvantages of Curb and Gutter
- Top 45 Greatest Constructions of Gothic Architecture in World | What Is Gothic Architecture | Unique Features Of Gothic Architecture
- What is Floating Foundation | Suitability of the Floating Foundation | Advantages & Disadvantage of Floating Foundation | How to Build a Floating House Foundation
[/su_note]