Table of Contents
H-Beam vs I-Beam
H Beam Vs I Beam, Structural steel has been used extensively in the construction of commercial buildings since the first steel-framed building, the Rand Mcnally Building erected in 1890.
Since then, steel has been used for major construction projects. The availability of steel makes it much easier to use.
First, it bonds well to concrete and has many features that make it even better than concrete when it comes to construction projects.
Steel is still one of the preferred material options in construction, as it takes less time to build and contributes to a perfect combination of lightness, high strength, and ease of manufacture.
It has been an important component in commercial construction projects. Speaking of steel, H and V beams are two of the most common structural members used in construction to provide support for buildings and walls. Let’s take a look at these two structural members.
What Is H-Beam?
H beam is a structural beam made of rolled steel. It is incredibly strong. It gets its name because it looks like a capital H over the cross-section.
H-beam has wider flanges than I-beam, but I-beam has tapered edges. The width is the flange and the height is the web.
The difference between the H and I beams is the flange per band ratio. The H beam tends to be heavier than the I beam, which is why some say it is better than the I beam, but this is subjective, as the H beam is generally heavier.
What Is I-Beam?
An I-beam is shaped like an I. The I-beam consists of two horizontal planes, known as flanges, connected by a vertical component or the weft.
I-beam has tapered edges and gets its name because it looks like a capital letter when you see it through the cross-section. With an I-beam, the height of the cross-section is greater than the width of its flange.
Useful Article for You
- What Is a Highway Flyover
- What Is Grouting
- What Is a Pile Cap
- What Is a Bond Beam in Masonry
- What Is Sapwood
- What Is Crane
- What Is a Gable
- What Is Superelevation
- What Is Kerb
- What Is the Purpose of Washers
- What Is the Size of a Brick in Inches
- What Is Reinforced Masonry
- What Is Workability
- What Is Bond Breaker
- What Is Plasticizer in Concrete
- What Is Luminous Flux Vs Lumens
- What Is Caisson
- What Is an Undercoat
- What Is a Benchmark Surveying
- What Is Bracing in Construction
- What Is a Beam in Construction
- What Is the Standard Door Frame Size
- What Is a Spandrel Beam
- What Is a Fire Escape
- What Is a Weep Hole
- What Is Tie Beam
- What Is Fine Aggregate
- What Is Pony Wall
- What Is Flag Stone
- What Is Development Length
- What Is Cement Plaster
- What Is a Pitched Roof
- What Is a Slab in Construction
- What Is a Monolithic Slab
- What Is Linear Distance
- What Is Shovel
- What Is Lintel in Construction
- What Is a Concept Sketch
- What Is Mezzanine Floor
- What Is Man Sand
- What Is Plaster Made Out of
- What Is a Floating Slab
- What Is Falsework
- What Is Bituminous
- What Is a Spillway
- What Is Curb and Gutter
- What Is Dampness
- What Is Lap Length
- What Is the Full Form of Fsi
- What Is Door Frame
- What Is Plinth Protection
- What Is Traffic Rotary
- What Is Grade Slab
- What Is Rolling Margin of Steel
- What Is Modulus of Rupture
- What Is Fresh Concrete
- What Is Dpc in Construction
- What Is Earthen Dam
- What Is Plum Concrete
- What Is Shell Structure.
- What Is Lumber
- What Is the Strongest Foundation for a House
- What Is the Meaning of Soundness of Cement
- What Is Flyover Bridge
- What Is Under Reamed Pile
- What Is Weir
Difference Between H-Beam and I-Beam
H-Beam and I-Beam: Basics of
The H beam, as the name suggests, is an H-shaped structural member made of rolled steel and is known as a wide flange beam.
It is one of the most used structural members in the United States. It looks like an ‘H’ over the cross-section and is incredibly strong and has a larger surface area in the cross-section of the beam.
I beam, on the other hand, is also known as an H beam, but it looks like an ‘I’ of the cross-section. It is basically a beam of rolled steel or a beam with a cross-section in the form of the capital letter I.
H-Beam and I-Beam: Projects
In terms of design, H beams have longer, wider and heavier flanges than I beams, but both terms H beam and I beam can be used interchangeably most of the time and are commonly called laminated steel beams (RSJ) The horizontal element at the top and bottom of a beam is called a flange, which is usually narrower on I-beams, but is almost equally wide as such.
The height of a beam is the web, which is thicker in H beams, which makes them relatively stronger than I beams. 1-beams, on the other hand, have thin webs and conical flanges.
H-Beam and I-Beam: Strength
The H-beams are made of economically sectioned steel, with a more optimized cross-sectional distribution area and a reasonable strength-to-weight ratio, which means it can provide more strength per unit weight.
This makes welding the H-beams relatively simpler than that of the I-beams. And due to its larger surface area in the cross-section, it is considered to have a high strength rate.
However, I-beams are generally deeper than wide, which makes them quite good for supporting load under local buckling. In addition, I beams are lighter than H beams, which means that they will not be able to withstand as much force as H beams.
Useful Article for You
- How Wide Is a Cinder Block
- How Much Is a Coffered Ceiling
- How to Make Mortar
- How Long Does Hempcrete Last
- How to Use a Hand Sight Level
- How to Construction
- How to Build a Lean to Roof
- How Are Tunnels Built
- How to Layout a Building
- How Wide Is a Car Parking Space
- How Do Shear Walls Work
- How to Measure Concrete Slump
- How to Use Washers with Screws
- How Dense Is Sand
- How High Is a Window from the Floor
- How to Fix Spalling Concrete Foundation
- How Does a Beam Bridge Work
- How Do They Pour Concrete Under Water
- How Does a Sewer System Work
- How High Are Countertops
- How to Seal Brick Wall Interior
- How to Resurface Cement
- How to Use Portland Cement
- How Is Plaster Made
- How to Find Fineness Modulus
- How to Get Rid of Spray Paint Smell on Metal
- How Many Types of Slope Are There
- How Big Is a Stair Landing
- How to Get Paint Off Concrete Without Chemicals
- How to Fix Water Damaged Drywall
- How Much to Get Septic Pumped
- How to Cut a Nail or Screw
- How Long Does Wet Concrete Take to Dry
- How Is Varnish Made
- How Does Ejector Pump Work
- How Does Hydrometer Work
- How to Get Wet Blood Out of Carpet
- How to Build House on Slope
- How Thick Is Plaster Wall
- How Suspension Bridges Work
- How to Seal a Concrete Roof
- How Was Cement Invented
- How to Calculate Area of Steel
- How to Check Silt Content in Sand
- How a Building Is Constructed
- How Are Roads Classified in India
- How Many Types of Cement in India
- How to Find Contour Interval
- How to Stop Leakage from Ceiling
- How Hardness of Brick Is Tested
- How Many Types of Paint Brushes Are There
- How to Calculate Skirting Area
- How Many Types of Beam
- How to Make Road
- How Many Types of Chain in Surveying
- How to Find One Way and Two Way Slab
- How Many Types of Houses
- How to Find Steel Bar Weight
H-Beam and I-Beam: Applications
Since H beams have thicker walls and flanges, they are ideal for mezzanines, platforms, bridges and other common residential and commercial buildings.
Wide flanges are commonly used in residential projects. The internal dimensions of the H-beams are constant, in order to make them the preferred choice of material in the structure of the trailer and truck.
I-beams, with their greater resistance to flanges, are the preferred form choice for structural steel buildings, bridges, and other civil projects.
In addition to commercial and residential construction projects, they are also used to make structures and support columns for rails, elevators, beds for trailers and trucks, winches and elevators.
Which Is The Heaviest?
- The H beam is generally much heavier than the I beam, which means it can receive more
- In some buildings where weight and strength on the wall can represent a structural problem, the I-beam may be better, as it is generally lighter.
- An H beam has a thicker central web, which means that it is generally stronger.
- An I beam generally has a thinner central web, which means that it is often not able to receive as much force as an H beam.
- An H beam can be mounted, which means that it can be mounted at any size or height.
- An I beam can only be constructed as long as the manufacturer’s milling equipment allows.
- H beams can be used for spans up to 330 feet.
- An I-beam can be used for spans from 33 to 100 feet.
- H-beam: H-beams have top and bottom flanges that stick out further from the web than the flanges on I-beams.
- I-beam: I-beams have top and bottom flanges, and they are shorter and are not as wide as H-beams.
Number of Pieces
- The H beam looks like a piece of metal but has a chamfer in which three pieces of metal come together.
- An I beam is not made by welding or riveting metal sheets together and is just a piece of metal throughout.
Although the terms beam H and I are often used interchangeably in the construction industry, saying that one is better than the other is quite subjective.
Both are the two most common structural steel beams used in various structural steelmakers, as support beams for the construction of commercial and residential buildings.
Both look almost the same on the outside, except that they differ in geometry. These are the two versions of steel structural beams used in a wide range of applications.
The H beam has an H-shaped cross-section, while the I beam has a cross-section in the form of the capital letter ‘I’.
Technically, an I-beam can be referred to as an H-beam with slightly different mechanical properties, such as strength/weight ratio, load capacity, tensile strength and so on.